Doctor Installation Guide

Doctor Configuration

OPNFV installers install most components of Doctor framework including OpenStack Nova, Neutron and Cinder (Doctor Controller) and OpenStack Ceilometer and Aodh (Doctor Notifier) except Doctor Monitor.

After major components of OPNFV are deployed, you can setup Doctor functions by following instructions in this section. You can also learn detailed steps in setup_installer() under doctor/tests.

Doctor Inspector

You need to configure one of Doctor Inspector below.

Doctor Sample Inspector

Sample Inspector is intended to show minimum functions of Doctor Inspector.

Doctor Sample Inspector suggested to be placed in one of the controller nodes, but it can be put on any host where Doctor Monitor can reach and access the OpenStack Controller (Nova).

Make sure OpenStack env parameters are set properly, so that Doctor Inspector can issue admin actions such as compute host force-down and state update of VM.

Then, you can configure Doctor Inspector as follows:

git clone https://gerrit.opnfv.org/gerrit/doctor -b stable/danube
cd doctor/tests
INSPECTOR_PORT=12345
python inspector.py $INSPECTOR_PORT > inspector.log 2>&1 &

Congress

OpenStack Congress is a Governance as a Service (previously Policy as a Service). Congress implements Doctor Inspector as it can inspect a fault situation and propagate errors onto other entities.

Congress is deployed by OPNFV installers. You need to enable doctor datasource driver and set policy rules. By the example configuration below, Congress will force down nova compute service when it received a fault event of that compute host. Also, Congress will set the state of all VMs running on that host from ACTIVE to ERROR state.

openstack congress datasource create doctor doctor

openstack congress policy rule create \
    --name host_down classification \
    'host_down(host) :-
        doctor:events(hostname=host, type="compute.host.down", status="down")'

openstack congress policy rule create \
    --name active_instance_in_host classification \
    'active_instance_in_host(vmid, host) :-
        nova:servers(id=vmid, host_name=host, status="ACTIVE")'

openstack congress policy rule create \
    --name host_force_down classification \
    'execute[nova:services.force_down(host, "nova-compute", "True")] :-
        host_down(host)'

openstack congress policy rule create \
    --name error_vm_states classification \
    'execute[nova:servers.reset_state(vmid, "error")] :-
        host_down(host),
        active_instance_in_host(vmid, host)'

Vitrage

OpenStack Vitrage is an RCA (Root Cause Analysis) service for organizing, analyzing and expanding OpenStack alarms & events. Vitrage implements Doctor Inspector, as it receives a notification that a host is down and calls Nova force-down API. In addition, it raises alarms on the instances running on this host.

Vitrage is not deployed by OPNFV installers yet. It can be installed either on top of a devstack environment, or on top of a real OpenStack environment. See Vitrage Installation

Doctor SB API and a Doctor datasource were implemented in Vitrage in the Ocata release. The Doctor datasource is enabled by default.

After Vitrage is installed and configured, there is a need to configure it to support the Doctor use case. This can be done in a few steps:

  1. Make sure that ‘aodh’ and ‘doctor’ are included in the list of datasource types in /etc/vitrage/vitrage.conf:
[datasources]
types = aodh,doctor,nova.host,nova.instance,nova.zone,static,cinder.volume,neutron.network,neutron.port,heat.stack
  1. Enable the Vitrage Nova notifier. Set the following line in /etc/vitrage/vitrage.conf:
[DEFAULT]
notifiers = nova
  1. Add a template that is responsible to call Nova force-down if Vitrage receives a ‘compute.host.down’ alarm. Copy template and place it under /etc/vitrage/templates
  1. Restart the vitrage-graph and vitrage-notifier services

Doctor Monitor

Doctor Sample Monitor

Doctor Monitors are suggested to be placed in one of the controller nodes, but those can be put on any host which is reachable to target compute host and accessible by the Doctor Inspector. You need to configure Monitors for all compute hosts one by one.

Make sure OpenStack env parameters are set properly, so that Doctor Inspector can issue admin actions such as compute host force-down and state update of VM.

Then, you can configure the Doctor Monitor as follows (Example for Apex deployment):

git clone https://gerrit.opnfv.org/gerrit/doctor -b stable/danube
cd doctor/tests
INSPECTOR_PORT=12345
COMPUTE_HOST='overcloud-novacompute-1.localdomain.com'
COMPUTE_IP=192.30.9.5
sudo python monitor.py "$COMPUTE_HOST" "$COMPUTE_IP" \
    "http://127.0.0.1:$INSPECTOR_PORT/events" > monitor.log 2>&1 &