VSPERF Installation Guide

1. Installing vswitchperf

1.1. Downloading vswitchperf

The vswitchperf can be downloaded from its official git repository, which is hosted by OPNFV. It is necessary to install a git at your DUT before downloading vswitchperf. Installation of git is specific to the packaging system used by Linux OS installed at DUT.

Example of installation of GIT package and its dependencies:

  • in case of OS based on RedHat Linux:

    sudo yum install git
    
  • in case of Ubuntu or Debian:

    sudo apt-get install git
    

After the git is successfully installed at DUT, then vswitchperf can be downloaded as follows:

git clone http://git.opnfv.org/vswitchperf

The last command will create a directory vswitchperf with a local copy of vswitchperf repository.

1.2. Supported Operating Systems

  • CentOS 7.3
  • Fedora 20
  • Fedora 21
  • Fedora 22
  • Fedora 24 (kernel 4.8 requires DPDK 16.11 and newer)
  • RedHat 7.2 Enterprise Linux
  • RedHat 7.3 Enterprise Linux
  • Ubuntu 14.04
  • Ubuntu 16.04
  • Ubuntu 16.10 (kernel 4.8 requires DPDK 16.11 and newer)

1.3. Supported vSwitches

The vSwitch must support Open Flow 1.3 or greater.

  • Open vSwitch
  • Open vSwitch with DPDK support
  • TestPMD application from DPDK (supports p2p and pvp scenarios)

1.4. Supported Hypervisors

  • Qemu version 2.3 or greater (version 2.5.0 is recommended)

1.5. Supported VNFs

In theory, it is possible to use any VNF image, which is compatible with supported hypervisor. However such VNF must ensure, that appropriate number of network interfaces is configured and that traffic is properly forwarded among them. For new vswitchperf users it is recommended to start with official vloop-vnf image, which is maintained by vswitchperf community.

1.5.1. vloop-vnf

The official VM image is called vloop-vnf and it is available for free download from OPNFV artifactory. This image is based on Linux Ubuntu distribution and it supports following applications for traffic forwarding:

  • DPDK testpmd
  • Linux Bridge
  • Custom l2fwd module

The vloop-vnf can be downloaded to DUT, for example by wget:

wget http://artifacts.opnfv.org/vswitchperf/vnf/vloop-vnf-ubuntu-14.04_20160823.qcow2

NOTE: In case that wget is not installed at your DUT, you could install it at RPM based system by sudo yum install wget or at DEB based system by sudo apt-get install wget.

Changelog of vloop-vnf:

1.6. Installation

The test suite requires Python 3.3 or newer and relies on a number of other system and python packages. These need to be installed for the test suite to function.

Installation of required packages, preparation of Python 3 virtual environment and compilation of OVS, DPDK and QEMU is performed by script systems/build_base_machine.sh. It should be executed under user account, which will be used for vsperf execution.

NOTE: Password-less sudo access must be configured for given user account before script is executed.

$ cd systems
$ ./build_base_machine.sh

NOTE: you don’t need to go into any of the systems subdirectories, simply run the top level build_base_machine.sh, your OS will be detected automatically.

Script build_base_machine.sh will install all the vsperf dependencies in terms of system packages, Python 3.x and required Python modules. In case of CentOS 7 or RHEL it will install Python 3.3 from an additional repository provided by Software Collections (a link). Installation script will also use virtualenv to create a vsperf virtual environment, which is isolated from the default Python environment. This environment will reside in a directory called vsperfenv in $HOME. It will ensure, that system wide Python installation is not modified or broken by VSPERF installation. The complete list of Python packages installed inside virtualenv can be found at file requirements.txt, which is located at vswitchperf repository.

NOTE: For RHEL 7.3 Enterprise and CentOS 7.3 OVS Vanilla is not built from upstream source due to kernel incompatibilities. Please see the instructions in the vswitchperf_design document for details on configuring OVS Vanilla for binary package usage.

1.7. Using vswitchperf

You will need to activate the virtual environment every time you start a new shell session. Its activation is specific to your OS:

  • CentOS 7 and RHEL

    $ scl enable python33 bash
    $ source $HOME/vsperfenv/bin/activate
    
  • Fedora and Ubuntu

    $ source $HOME/vsperfenv/bin/activate
    

After the virtual environment is configued, then VSPERF can be used. For example:

(vsperfenv) $ cd vswitchperf
(vsperfenv) $ ./vsperf --help

1.7.1. Gotcha

In case you will see following error during environment activation:

$ source $HOME/vsperfenv/bin/activate
Badly placed ()'s.

then check what type of shell you are using:

$ echo $SHELL
/bin/tcsh

See what scripts are available in $HOME/vsperfenv/bin

$ ls $HOME/vsperfenv/bin/
activate          activate.csh      activate.fish     activate_this.py

source the appropriate script

$ source bin/activate.csh

1.7.2. Working Behind a Proxy

If you’re behind a proxy, you’ll likely want to configure this before running any of the above. For example:

export http_proxy=proxy.mycompany.com:123
export https_proxy=proxy.mycompany.com:123

1.8. Hugepage Configuration

Systems running vsperf with either dpdk and/or tests with guests must configure hugepage amounts to support running these configurations. It is recommended to configure 1GB hugepages as the pagesize.

The amount of hugepages needed depends on your configuration files in vsperf. Each guest image requires 2048 MB by default according to the default settings in the 04_vnf.conf file.

GUEST_MEMORY = ['2048']

The dpdk startup parameters also require an amount of hugepages depending on your configuration in the 02_vswitch.conf file.

VSWITCHD_DPDK_ARGS = ['-c', '0x4', '-n', '4', '--socket-mem 1024,1024']
VSWITCHD_DPDK_CONFIG = {
    'dpdk-init' : 'true',
    'dpdk-lcore-mask' : '0x4',
    'dpdk-socket-mem' : '1024,1024',
}

NOTE: Option VSWITCHD_DPDK_ARGS is used for vswitchd, which supports --dpdk parameter. In recent vswitchd versions, option VSWITCHD_DPDK_CONFIG is used to configure vswitchd via ovs-vsctl calls.

With the --socket-mem argument set to use 1 hugepage on the specified sockets as seen above, the configuration will need 10 hugepages total to run all tests within vsperf if the pagesize is set correctly to 1GB.

VSPerf will verify hugepage amounts are free before executing test environments. In case of hugepage amounts not being free, test initialization will fail and testing will stop.

NOTE: In some instances on a test failure dpdk resources may not release hugepages used in dpdk configuration. It is recommended to configure a few extra hugepages to prevent a false detection by VSPerf that not enough free hugepages are available to execute the test environment. Normally dpdk would use previously allocated hugepages upon initialization.

Depending on your OS selection configuration of hugepages may vary. Please refer to your OS documentation to set hugepages correctly. It is recommended to set the required amount of hugepages to be allocated by default on reboots.

Information on hugepage requirements for dpdk can be found at http://dpdk.org/doc/guides/linux_gsg/sys_reqs.html

You can review your hugepage amounts by executing the following command

cat /proc/meminfo | grep Huge

If no hugepages are available vsperf will try to automatically allocate some. Allocation is controlled by HUGEPAGE_RAM_ALLOCATION configuration parameter in 02_vswitch.conf file. Default is 2GB, resulting in either 2 1GB hugepages or 1024 2MB hugepages.

2. Upgrading vswitchperf

2.1. Generic

In case, that VSPERF is cloned from git repository, then it is easy to upgrade it to the newest stable version or to the development version.

You could get a list of stable releases by git command. It is necessary to update local git repository first.

NOTE: Git commands must be executed from directory, where VSPERF repository was cloned, e.g. vswitchperf.

Update of local git repository:

$ git pull

List of stable releases:

$ git tag

brahmaputra.1.0
colorado.1.0
colorado.2.0
colorado.3.0
danube.1.0

You could select which stable release should be used. For example, select danube.1.0:

$ git checkout danube.1.0

Development version of VSPERF can be selected by:

$ git checkout master

2.2. Colorado to Danube upgrade notes

2.2.1. Obsoleted features

Support of vHost Cuse interface has been removed in Danube release. It means, that it is not possible to select QemuDpdkVhostCuse as a VNF anymore. Option QemuDpdkVhostUser should be used instead. Please check you configuration files and definition of your testcases for any occurrence of:

VNF = "QemuDpdkVhostCuse"

or

"VNF" : "QemuDpdkVhostCuse"

In case that QemuDpdkVhostCuse is found, it must be modified to QemuDpdkVhostUser.

NOTE: In case that execution of VSPERF is automated by scripts (e.g. for CI purposes), then these scripts must be checked and updated too. It means, that any occurrence of:

./vsperf --vnf QemuDpdkVhostCuse

must be updated to:

./vsperf --vnf QemuDpdkVhostUser

2.2.2. Configuration

Several configuration changes were introduced during Danube release. The most important changes are discussed below.

2.2.2.1. Paths to DPDK, OVS and QEMU

VSPERF uses external tools for proper testcase execution. Thus it is important to properly configure paths to these tools. In case that tools are installed by installation scripts and are located inside ./src directory inside VSPERF home, then no changes are needed. On the other hand, if path settings was changed by custom configuration file, then it is required to update configuration accordingly. Please check your configuration files for following configuration options:

OVS_DIR
OVS_DIR_VANILLA
OVS_DIR_USER
OVS_DIR_CUSE

RTE_SDK_USER
RTE_SDK_CUSE

QEMU_DIR
QEMU_DIR_USER
QEMU_DIR_CUSE
QEMU_BIN

In case that any of these options is defined, then configuration must be updated. All paths to the tools are now stored inside PATHS dictionary. Please refer to the paths-documentation and update your configuration where necessary.

2.2.2.2. Configuration change via CLI

In previous releases it was possible to modify selected configuration options (mostly VNF specific) via command line interface, i.e. by --test-params argument. This concept has been generalized in Danube release and it is possible to modify any configuration parameter via CLI or via Parameters section of the testcase definition. Old configuration options were obsoleted and it is required to specify configuration parameter name in the same form as it is defined inside configuration file, i.e. in uppercase. Please refer to the overriding-parameters-documentation for additional details.

NOTE: In case that execution of VSPERF is automated by scripts (e.g. for CI purposes), then these scripts must be checked and updated too. It means, that any occurrence of

guest_loopback
vanilla_tgen_port1_ip
vanilla_tgen_port1_mac
vanilla_tgen_port2_ip
vanilla_tgen_port2_mac
tunnel_type

shall be changed to the uppercase form and data type of entered values must match to data types of original values from configuration files.

In case that guest_nic1_name or guest_nic2_name is changed, then new dictionary GUEST_NICS must be modified accordingly. Please see guest-configuration and conf/04_vnf.conf for additional details.

2.2.2.3. Traffic configuration via CLI

In previous releases it was possible to modify selected attributes of generated traffic via command line interface. This concept has been enhanced in Danube release and it is now possible to modify all traffic specific options via CLI or by TRAFFIC dictionary in configuration file. Detailed description is available at configuration-of-traffic-dictionary section of documentation.

Please check your automated scripts for VSPERF execution for following CLI parameters and update them according to the documentation:

bidir
duration
frame_rate
iload
lossrate
multistream
pkt_sizes
pre-installed_flows
rfc2544_tests
stream_type
traffic_type

3. ‘vsperf’ Traffic Gen Guide

3.1. Overview

VSPERF supports the following traffic generators:

To see the list of traffic gens from the cli:

$ ./vsperf --list-trafficgens

This guide provides the details of how to install and configure the various traffic generators.

3.2. Background Information

The traffic default configuration can be found in conf/03_traffic.conf, and is configured as follows:

TRAFFIC = {
    'traffic_type' : 'rfc2544_throughput',
    'frame_rate' : 100,
    'bidir' : 'True',  # will be passed as string in title format to tgen
    'multistream' : 0,
    'stream_type' : 'L4',
    'pre_installed_flows' : 'No',           # used by vswitch implementation
    'flow_type' : 'port',                   # used by vswitch implementation

    'l2': {
        'framesize': 64,
        'srcmac': '00:00:00:00:00:00',
        'dstmac': '00:00:00:00:00:00',
    },
    'l3': {
        'proto': 'udp',
        'srcip': '1.1.1.1',
        'dstip': '90.90.90.90',
    },
    'l4': {
        'srcport': 3000,
        'dstport': 3001,
    },
    'vlan': {
        'enabled': False,
        'id': 0,
        'priority': 0,
        'cfi': 0,
    },
}

The framesize parameter can be overridden from the configuration files by adding the following to your custom configuration file 10_custom.conf:

TRAFFICGEN_PKT_SIZES = (64, 128,)

OR from the commandline:

$ ./vsperf --test-params "TRAFFICGEN_PKT_SIZES=(x,y)" $TESTNAME

You can also modify the traffic transmission duration and the number of tests run by the traffic generator by extending the example commandline above to:

$ ./vsperf --test-params "TRAFFICGEN_PKT_SIZES=(x,y);TRAFFICGEN_DURATION=10;" \
                         "TRAFFICGEN_RFC2544_TESTS=1" $TESTNAME

3.3. Dummy

The Dummy traffic generator can be used to test VSPERF installation or to demonstrate VSPERF functionality at DUT without connection to a real traffic generator.

You could also use the Dummy generator in case, that your external traffic generator is not supported by VSPERF. In such case you could use VSPERF to setup your test scenario and then transmit the traffic. After the transmission is completed you could specify values for all collected metrics and VSPERF will use them to generate final reports.

3.3.1. Setup

To select the Dummy generator please add the following to your custom configuration file 10_custom.conf.

TRAFFICGEN = 'Dummy'

OR run vsperf with the --trafficgen argument

$ ./vsperf --trafficgen Dummy $TESTNAME

Where $TESTNAME is the name of the vsperf test you would like to run. This will setup the vSwitch and the VNF (if one is part of your test) print the traffic configuration and prompt you to transmit traffic when the setup is complete.

Please send 'continuous' traffic with the following stream config:
30mS, 90mpps, multistream False
and the following flow config:
{
    "flow_type": "port",
    "l3": {
        "srcip": "1.1.1.1",
        "proto": "tcp",
        "dstip": "90.90.90.90"
    },
    "traffic_type": "rfc2544_continuous",
    "multistream": 0,
    "bidir": "True",
    "vlan": {
        "cfi": 0,
        "priority": 0,
        "id": 0,
        "enabled": false
    },
    "frame_rate": 90,
    "l2": {
        "dstport": 3001,
        "srcport": 3000,
        "dstmac": "00:00:00:00:00:00",
        "srcmac": "00:00:00:00:00:00",
        "framesize": 64
    }
}
What was the result for 'frames tx'?

When your traffic generator has completed traffic transmission and provided the results please input these at the VSPERF prompt. VSPERF will try to verify the input:

Is '$input_value' correct?

Please answer with y OR n.

VSPERF will ask you to provide a value for every of collected metrics. The list of metrics can be found at traffic-type-metrics. Finally vsperf will print out the results for your test and generate the appropriate logs and report files.

3.3.2. Metrics collected for supported traffic types

Below you could find a list of metrics collected by VSPERF for each of supported traffic types.

RFC2544 Throughput and Continuous:

  • frames tx
  • frames rx
  • min latency
  • max latency
  • avg latency
  • frameloss

RFC2544 Back2back:

  • b2b frames
  • b2b frame loss %

3.3.3. Dummy result pre-configuration

In case of a Dummy traffic generator it is possible to pre-configure the test results. This is useful for creation of demo testcases, which do not require a real traffic generator. Such testcase can be run by any user and it will still generate all reports and result files.

Result values can be specified within TRAFFICGEN_DUMMY_RESULTS dictionary, where every of collected metrics must be properly defined. Please check the list of traffic-type-metrics.

Dictionary with dummy results can be passed by CLI argument --test-params or specified in Parameters section of testcase definition.

Example of testcase execution with dummy results defined by CLI argument:

$ ./vsperf back2back --trafficgen Dummy --test-params \
  "TRAFFICGEN_DUMMY_RESULTS={'b2b frames':'3000','b2b frame loss %':'0.0'}"

Example of testcase definition with pre-configured dummy results:

{
    "Name": "back2back",
    "Traffic Type": "rfc2544_back2back",
    "Deployment": "p2p",
    "biDirectional": "True",
    "Description": "LTD.Throughput.RFC2544.BackToBackFrames",
    "Parameters" : {
        'TRAFFICGEN_DUMMY_RESULTS' : {'b2b frames':'3000','b2b frame loss %':'0.0'}
    },
},

NOTE: Pre-configured results for the Dummy traffic generator will be used only in case, that the Dummy traffic generator is used. Otherwise the option TRAFFICGEN_DUMMY_RESULTS will be ignored.

3.4. Ixia

VSPERF can use both IxNetwork and IxExplorer TCL servers to control Ixia chassis. However usage of IxNetwork TCL server is a preferred option. Following sections will describe installation and configuration of IxNetwork components used by VSPERF.

3.4.1. Installation

On the system under the test you need to install IxNetworkTclClient$(VER_NUM)Linux.bin.tgz.

On the IXIA client software system you need to install IxNetwork TCL server. After its installation you should configure it as follows:

  1. Find the IxNetwork TCL server app (start -> All Programs -> IXIA -> IxNetwork -> IxNetwork_$(VER_NUM) -> IxNetwork TCL Server)

  2. Right click on IxNetwork TCL Server, select properties - Under shortcut tab in the Target dialogue box make sure there is the argument “-tclport xxxx” where xxxx is your port number (take note of this port number as you will need it for the 10_custom.conf file).

    _images/TCLServerProperties.png
  3. Hit Ok and start the TCL server application

3.4.2. VSPERF configuration

There are several configuration options specific to the IxNetwork traffic generator from IXIA. It is essential to set them correctly, before the VSPERF is executed for the first time.

Detailed description of options follows:

  • TRAFFICGEN_IXNET_MACHINE - IP address of server, where IxNetwork TCL Server is running
  • TRAFFICGEN_IXNET_PORT - PORT, where IxNetwork TCL Server is accepting connections from TCL clients
  • TRAFFICGEN_IXNET_USER - username, which will be used during communication with IxNetwork TCL Server and IXIA chassis
  • TRAFFICGEN_IXIA_HOST - IP address of IXIA traffic generator chassis
  • TRAFFICGEN_IXIA_CARD - identification of card with dedicated ports at IXIA chassis
  • TRAFFICGEN_IXIA_PORT1 - identification of the first dedicated port at TRAFFICGEN_IXIA_CARD at IXIA chassis; VSPERF uses two separated ports for traffic generation. In case of unidirectional traffic, it is essential to correctly connect 1st IXIA port to the 1st NIC at DUT, i.e. to the first PCI handle from WHITELIST_NICS list. Otherwise traffic may not be able to pass through the vSwitch.
  • TRAFFICGEN_IXIA_PORT2 - identification of the second dedicated port at TRAFFICGEN_IXIA_CARD at IXIA chassis; VSPERF uses two separated ports for traffic generation. In case of unidirectional traffic, it is essential to correctly connect 2nd IXIA port to the 2nd NIC at DUT, i.e. to the second PCI handle from WHITELIST_NICS list. Otherwise traffic may not be able to pass through the vSwitch.
  • TRAFFICGEN_IXNET_LIB_PATH - path to the DUT specific installation of IxNetwork TCL API
  • TRAFFICGEN_IXNET_TCL_SCRIPT - name of the TCL script, which VSPERF will use for communication with IXIA TCL server
  • TRAFFICGEN_IXNET_TESTER_RESULT_DIR - folder accessible from IxNetwork TCL server, where test results are stored, e.g. c:/ixia_results; see test-results-share
  • TRAFFICGEN_IXNET_DUT_RESULT_DIR - directory accessible from the DUT, where test results from IxNetwork TCL server are stored, e.g. /mnt/ixia_results; see test-results-share

3.4.3. Test results share

VSPERF is not able to retrieve test results via TCL API directly. Instead, all test results are stored at IxNetwork TCL server. Results are stored at folder defined by TRAFFICGEN_IXNET_TESTER_RESULT_DIR configuration parameter. Content of this folder must be shared (e.g. via samba protocol) between TCL Server and DUT, where VSPERF is executed. VSPERF expects, that test results will be available at directory configured by TRAFFICGEN_IXNET_DUT_RESULT_DIR configuration parameter.

Example of sharing configuration:

  • Create a new folder at IxNetwork TCL server machine, e.g. c:\ixia_results

  • Modify sharing options of ixia_results folder to share it with everybody

  • Create a new directory at DUT, where shared directory with results will be mounted, e.g. /mnt/ixia_results

  • Update your custom VSPERF configuration file as follows:

    TRAFFICGEN_IXNET_TESTER_RESULT_DIR = 'c:/ixia_results'
    TRAFFICGEN_IXNET_DUT_RESULT_DIR = '/mnt/ixia_results'
    

    NOTE: It is essential to use slashes ‘/’ also in path configured by TRAFFICGEN_IXNET_TESTER_RESULT_DIR parameter.

  • Install cifs-utils package.

    e.g. at rpm based Linux distribution:

    yum install cifs-utils
    
  • Mount shared directory, so VSPERF can access test results.

    e.g. by adding new record into /etc/fstab

    mount -t cifs //_TCL_SERVER_IP_OR_FQDN_/ixia_results /mnt/ixia_results
          -o file_mode=0777,dir_mode=0777,nounix
    

It is recommended to verify, that any new file inserted into c:/ixia_results folder is visible at DUT inside /mnt/ixia_results directory.

3.5. Spirent Setup

Spirent installation files and instructions are available on the Spirent support website at:

http://support.spirent.com

Select a version of Spirent TestCenter software to utilize. This example will use Spirent TestCenter v4.57 as an example. Substitute the appropriate version in place of ‘v4.57’ in the examples, below.

3.5.1. On the CentOS 7 System

Download and install the following:

Spirent TestCenter Application, v4.57 for 64-bit Linux Client

3.5.2. Spirent Virtual Deployment Service (VDS)

Spirent VDS is required for both TestCenter hardware and virtual chassis in the vsperf environment. For installation, select the version that matches the Spirent TestCenter Application version. For v4.57, the matching VDS version is 1.0.55. Download either the ova (VMware) or qcow2 (QEMU) image and create a VM with it. Initialize the VM according to Spirent installation instructions.

3.5.3. Using Spirent TestCenter Virtual (STCv)

STCv is available in both ova (VMware) and qcow2 (QEMU) formats. For VMware, download:

Spirent TestCenter Virtual Machine for VMware, v4.57 for Hypervisor - VMware ESX.ESXi

Virtual test port performance is affected by the hypervisor configuration. For best practice results in deploying STCv, the following is suggested:

  • Create a single VM with two test ports rather than two VMs with one port each
  • Set STCv in DPDK mode
  • Give STCv 2*n + 1 cores, where n = the number of ports. For vsperf, cores = 5.
  • Turning off hyperthreading and pinning these cores will improve performance
  • Give STCv 2 GB of RAM

To get the highest performance and accuracy, Spirent TestCenter hardware is recommended. vsperf can run with either stype test ports.

3.5.4. Using STC REST Client

The stcrestclient package provides the stchttp.py ReST API wrapper module. This allows simple function calls, nearly identical to those provided by StcPython.py, to be used to access TestCenter server sessions via the STC ReST API. Basic ReST functionality is provided by the resthttp module, and may be used for writing ReST clients independent of STC.

To use REST interface, follow the instructions in the Project page to install the package. Once installed, the scripts named with ‘rest’ keyword can be used. For example: testcenter-rfc2544-rest.py can be used to run RFC 2544 tests using the REST interface.

3.5.5. Configuration:

  1. The Labserver and license server addresses. These parameters applies to all the tests, and are mandatory for all tests.
TRAFFICGEN_STC_LAB_SERVER_ADDR = " "
TRAFFICGEN_STC_LICENSE_SERVER_ADDR = " "
TRAFFICGEN_STC_PYTHON2_PATH = " "
TRAFFICGEN_STC_TESTCENTER_PATH = " "
TRAFFICGEN_STC_TEST_SESSION_NAME = " "
TRAFFICGEN_STC_CSV_RESULTS_FILE_PREFIX = " "
  1. For RFC2544 tests, the following parameters are mandatory
TRAFFICGEN_STC_EAST_CHASSIS_ADDR = " "
TRAFFICGEN_STC_EAST_SLOT_NUM = " "
TRAFFICGEN_STC_EAST_PORT_NUM = " "
TRAFFICGEN_STC_EAST_INTF_ADDR = " "
TRAFFICGEN_STC_EAST_INTF_GATEWAY_ADDR = " "
TRAFFICGEN_STC_WEST_CHASSIS_ADDR = ""
TRAFFICGEN_STC_WEST_SLOT_NUM = " "
TRAFFICGEN_STC_WEST_PORT_NUM = " "
TRAFFICGEN_STC_WEST_INTF_ADDR = " "
TRAFFICGEN_STC_WEST_INTF_GATEWAY_ADDR = " "
TRAFFICGEN_STC_RFC2544_TPUT_TEST_FILE_NAME
  1. RFC2889 tests: Currently, the forwarding, address-caching, and address-learning-rate tests of RFC2889 are supported. The testcenter-rfc2889-rest.py script implements the rfc2889 tests. The configuration for RFC2889 involves test-case definition, and parameter definition, as described below. New results-constants, as shown below, are added to support these tests.

Example of testcase definition for RFC2889 tests:

{
    "Name": "phy2phy_forwarding",
    "Deployment": "p2p",
    "Description": "LTD.Forwarding.RFC2889.MaxForwardingRate",
    "Parameters" : {
        "TRAFFIC" : {
            "traffic_type" : "rfc2889_forwarding",
        },
    },
}

For RFC2889 tests, specifying the locations for the monitoring ports is mandatory. Necessary parameters are:

Other Configurations are :

TRAFFICGEN_STC_RFC2889_MIN_LR = 1488
TRAFFICGEN_STC_RFC2889_MAX_LR = 14880
TRAFFICGEN_STC_RFC2889_MIN_ADDRS = 1000
TRAFFICGEN_STC_RFC2889_MAX_ADDRS = 65536
TRAFFICGEN_STC_RFC2889_AC_LR = 1000

The first 2 values are for address-learning test where as other 3 values are for the Address caching capacity test. LR: Learning Rate. AC: Address Caching. Maximum value for address is 16777216. Whereas, maximum for LR is 4294967295.

Results for RFC2889 Tests: Forwarding tests outputs following values:

TX_RATE_FPS : "Transmission Rate in Frames/sec"
THROUGHPUT_RX_FPS: "Received Throughput Frames/sec"
TX_RATE_MBPS : " Transmission rate in MBPS"
THROUGHPUT_RX_MBPS: "Received Throughput in MBPS"
TX_RATE_PERCENT: "Transmission Rate in Percentage"
FRAME_LOSS_PERCENT: "Frame loss in Percentage"
FORWARDING_RATE_FPS: " Maximum Forwarding Rate in FPS"

Whereas, the address caching test outputs following values,

CACHING_CAPACITY_ADDRS = 'Number of address it can cache'
ADDR_LEARNED_PERCENT = 'Percentage of address successfully learned'

and address learning test outputs just a single value:

OPTIMAL_LEARNING_RATE_FPS = 'Optimal learning rate in fps'

Note that ‘FORWARDING_RATE_FPS’, ‘CACHING_CAPACITY_ADDRS’, ‘ADDR_LEARNED_PERCENT’ and ‘OPTIMAL_LEARNING_RATE_FPS’ are the new result-constants added to support RFC2889 tests.

3.6. Xena Networks

3.6.1. Installation

Xena Networks traffic generator requires specific files and packages to be installed. It is assumed the user has access to the Xena2544.exe file which must be placed in VSPerf installation location under the tools/pkt_gen/xena folder. Contact Xena Networks for the latest version of this file. The user can also visit www.xenanetworks/downloads to obtain the file with a valid support contract.

Note VSPerf has been fully tested with version v2.43 of Xena2544.exe

To execute the Xena2544.exe file under Linux distributions the mono-complete package must be installed. To install this package follow the instructions below. Further information can be obtained from http://www.mono-project.com/docs/getting-started/install/linux/

rpm --import "http://keyserver.ubuntu.com/pks/lookup?op=get&search=0x3FA7E0328081BFF6A14DA29AA6A19B38D3D831EF"
yum-config-manager --add-repo http://download.mono-project.com/repo/centos/
yum -y install mono-complete

To prevent gpg errors on future yum installation of packages the mono-project repo should be disabled once installed.

yum-config-manager --disable download.mono-project.com_repo_centos_

3.6.2. Configuration

Connection information for your Xena Chassis must be supplied inside the 10_custom.conf or 03_custom.conf file. The following parameters must be set to allow for proper connections to the chassis.

TRAFFICGEN_XENA_IP = ''
TRAFFICGEN_XENA_PORT1 = ''
TRAFFICGEN_XENA_PORT2 = ''
TRAFFICGEN_XENA_USER = ''
TRAFFICGEN_XENA_PASSWORD = ''
TRAFFICGEN_XENA_MODULE1 = ''
TRAFFICGEN_XENA_MODULE2 = ''

3.6.3. RFC2544 Throughput Testing

Xena traffic generator testing for rfc2544 throughput can be modified for different behaviors if needed. The default options for the following are optimized for best results.

TRAFFICGEN_XENA_2544_TPUT_INIT_VALUE = '10.0'
TRAFFICGEN_XENA_2544_TPUT_MIN_VALUE = '0.1'
TRAFFICGEN_XENA_2544_TPUT_MAX_VALUE = '100.0'
TRAFFICGEN_XENA_2544_TPUT_VALUE_RESOLUTION = '0.5'
TRAFFICGEN_XENA_2544_TPUT_USEPASS_THRESHHOLD = 'false'
TRAFFICGEN_XENA_2544_TPUT_PASS_THRESHHOLD = '0.0'

Each value modifies the behavior of rfc 2544 throughput testing. Refer to your Xena documentation to understand the behavior changes in modifying these values.

3.6.4. Continuous Traffic Testing

Xena continuous traffic by default does a 3 second learning preemption to allow the DUT to receive learning packets before a continuous test is performed. If a custom test case requires this learning be disabled, you can disable the option or modify the length of the learning by modifying the following settings.

TRAFFICGEN_XENA_CONT_PORT_LEARNING_ENABLED = False
TRAFFICGEN_XENA_CONT_PORT_LEARNING_DURATION = 3

3.7. MoonGen

3.7.1. Installation

MoonGen architecture overview and general installation instructions can be found here:

https://github.com/emmericp/MoonGen

  • Note: Today, MoonGen with VSPERF only supports 10Gbps line speeds.

For VSPERF use, MoonGen should be cloned from here (as opposed to the previously mentioned GitHub):

git clone https://github.com/atheurer/lua-trafficgen

and use the master branch:

git checkout master

VSPERF uses a particular Lua script with the MoonGen project:

trafficgen.lua

Follow MoonGen set up and execution instructions here:

https://github.com/atheurer/lua-trafficgen/blob/master/README.md

Note one will need to set up ssh login to not use passwords between the server running MoonGen and the device under test (running the VSPERF test infrastructure). This is because VSPERF on one server uses ‘ssh’ to configure and run MoonGen upon the other server.

One can set up this ssh access by doing the following on both servers:

ssh-keygen -b 2048 -t rsa
ssh-copy-id <other server>

3.7.2. Configuration

Connection information for MoonGen must be supplied inside the 10_custom.conf or 03_custom.conf file. The following parameters must be set to allow for proper connections to the host with MoonGen.

TRAFFICGEN_MOONGEN_HOST_IP_ADDR = ""
TRAFFICGEN_MOONGEN_USER = ""
TRAFFICGEN_MOONGEN_BASE_DIR = ""
TRAFFICGEN_MOONGEN_PORTS = ""
TRAFFICGEN_MOONGEN_LINE_SPEED_GBPS = ""