Installation High-Level Overview - Bare Metal Deployment ======================================================== The setup presumes that you have 6 or more bare metal servers already setup with network connectivity on at least 2 interfaces for all servers via a TOR switch or other network implementation. The physical TOR switches are **not** automatically configured from the OPNFV reference platform. All the networks involved in the OPNFV infrastructure as well as the provider networks and the private tenant VLANs needs to be manually configured. The Jumphost can be installed using the bootable ISO or by other means including the (``opnfv-apex*.rpm``) RPMs and virtualization capabilities. The Jumphost should then be configured with an IP gateway on its admin or public interface and configured with a working DNS server. The Jumphost should also have routable access to the lights out network. ``opnfv-deploy`` is then executed in order to deploy the Undercloud VM. ``opnfv-deploy`` uses three configuration files in order to know how to install and provision the OPNFV target system. The information gathered under section `Execution Requirements (Bare Metal Only)`_ is put into the YAML file ``/etc/opnfv-apex/inventory.yaml`` configuration file. Deployment options are put into the YAML file ``/etc/opnfv-apex/deploy_settings.yaml``. Alternatively there are pre-baked deploy_settings files available in ``/etc/opnfv-apex/``. These files are named with the naming convention os-sdn_controller-enabled_feature-[no]ha.yaml. These files can be used in place of the ``/etc/opnfv-apex/deploy_settings.yaml`` file if one suites your deployment needs. Networking definitions gathered under section `Network Requirements`_ are put into the YAML file ``/etc/opnfv-apex/network_settings.yaml``. ``opnfv-deploy`` will boot the Undercloud VM and load the target deployment configuration into the provisioning toolchain. This includes MAC address, IPMI, Networking Environment and OPNFV deployment options. Once configuration is loaded and the Undercloud is configured it will then reboot the nodes via IPMI. The nodes should already be set to PXE boot first off the admin interface. The nodes will first PXE off of the Undercloud PXE server and go through a discovery/introspection process. Introspection boots off of custom introspection PXE images. These images are designed to look at the properties of the hardware that is booting off of them and report the properties of it back to the Undercloud node. After introspection Undercloud will execute a Heat Stack Deployment to being node provisioning and configuration. The nodes will reboot and PXE again off the Undercloud PXE server to provision each node using the Glance disk images provided by Undercloud These disk images include all the necessary packages and configuration for an OPNFV deployment to execute. Once the node's disk images have been written to disk the nodes will boot off the newly written disks and execute cloud-init which will execute the final node configuration. This configuration is largly completed by executing a puppet apply on each node. Installation High-Level Overview - VM Deployment ================================================ The VM nodes deployment operates almost the same way as the bare metal deployment with a few differences. ``opnfv-deploy`` still deploys an Undercloud VM. In addition to the Undercloud VM a collection of VMs (3 control nodes + 2 compute for an HA deployment or 1 control node and 1 compute node for a Non-HA Deployment) will be defined for the target OPNFV deployment. The part of the toolchain that executes IPMI power instructions calls into libvirt instead of the IPMI interfaces on baremetal servers to operate the power managment. These VMs are then provisioned with the same disk images and configuration that baremetal would be. To Triple-O these nodes look like they have just built and registered the same way as bare metal nodes, the main difference is the use of a libvirt driver for the power management. Installation Guide - Bare Metal Deployment ========================================== This section goes step-by-step on how to correctly install and provision the OPNFV target system to bare metal nodes. Install Bare Metal Jumphost --------------------------- 1a. If your Jumphost does not have CentOS 7 already on it, or you would like to do a fresh install, then download the Apex bootable ISO from OPNFV artifacts . There have been isolated reports of problems with the ISO having trouble completing installation successfully. In the unexpected event the ISO does not work please workaround this by downloading the CentOS 7 DVD and performing a "Virtualization Host" install. If you perform a "Minimal Install" or install type other than "Virtualization Host" simply run ``sudo yum groupinstall "Virtualization Host" && chkconfig libvirtd on && reboot`` to install virtualzation support and enable libvirt on boot. If you use the CentOS 7 DVD proceed to step 1b once the CentOS 7 with "Virtualzation Host" support is completed. 1b. If your Jump host already has CentOS 7 with libvirt running on it then install the install the RDO Release RPM: ``sudo yum install -y https://www.rdoproject.org/repos/rdo-release.rpm opnfv-apex-{version}.rpm`` The RDO Project release repository is needed to install OpenVSwitch, which is a dependency of opnfv-apex. If you do not have external connectivity to use this repository you need to download the OpenVSwitch RPM from the RDO Project repositories and install it with the opnfv-apex RPM. 2a. Boot the ISO off of a USB or other installation media and walk through installing OPNFV CentOS 7. The ISO comes prepared to be written directly to a USB drive with dd as such: ``dd if=opnfv-apex.iso of=/dev/sdX bs=4M`` Replace /dev/sdX with the device assigned to your usb drive. Then select the USB device as the boot media on your Jumphost 2b. If your Jump host already has CentOS 7 with libvirt running on it then install the opnfv-apex RPMs from OPNFV artifacts . The following RPMS are available for installation: - opnfv-apex - OpenDaylight L2 / L3 and ONOS support ** - opnfv-apex-onos - ONOS support ** - opnfv-apex-opendaylight-sfc - OpenDaylight SFC support ** - opnfv-apex-undercloud - (required) Undercloud Image - opnfv-apex-common - (required) Supporting config files and scripts ** One or more of these RPMs is required Only one of opnfv-apex, opnfv-apex-onos and opnfv-apex-opendaylight-sfc is required. It is safe to leave the unneeded SDN controller's RPMs uninstalled if you do not intend to use them. To install these RPMs download them to the local disk on your CentOS 7 install and pass the file names directly to yum: ``sudo yum install opnfv-apex-.rpm opnfv-apex-undercloud-.rpm opnfv-apex-common-.rpm`` 3. After the operating system and the opnfv-apex RPMs are installed, login to your Jumphost as root. 4. Configure IP addresses on the interfaces that you have selected as your networks. 5. Configure the IP gateway to the Internet either, preferably on the public interface. 6. Configure your ``/etc/resolv.conf`` to point to a DNS server (8.8.8.8 is provided by Google). Creating a Node Inventory File ------------------------------ IPMI configuration information gathered in section `Execution Requirements (Bare Metal Only)`_ needs to be added to the ``inventory.yaml`` file. 1. Copy ``/usr/share/doc/opnfv/inventory.yaml.example`` as your inventory file template to ``/etc/opnfv-apex/inventory.yaml``. 2. The nodes dictionary contains a definition block for each baremetal host that will be deployed. 1 or more compute nodes and 3 controller nodes are required. (The example file contains blocks for each of these already). It is optional at this point to add more compute nodes into the node list. 3. Edit the following values for each node: - ``mac_address``: MAC of the interface that will PXE boot from Undercloud - ``ipmi_ip``: IPMI IP Address - ``ipmi_user``: IPMI username - ``ipmi_password``: IPMI password - ``pm_type``: Power Management driver to use for the node - ``cpus``: (Introspected*) CPU cores available - ``memory``: (Introspected*) Memory available in Mib - ``disk``: (Introspected*) Disk space available in Gb - ``arch``: (Introspected*) System architecture - ``capabilities``: (Optional**) Intended node role (profile:control or profile:compute) * Introspection looks up the overcloud node's resources and overrides these value. You can leave default values and Apex will get the correct values when it runs introspection on the nodes. ** If capabilities profile is not specified then Apex will select node's roles in the OPNFV cluster in a non-deterministic fashion. Creating the Settings Files --------------------------- Edit the 2 settings files in /etc/opnfv-apex/. These files have comments to help you customize them. 1. deploy_settings.yaml This file includes basic configuration options deployment. Alternatively, there are pre-built deploy_settings files available in (``/etc/opnfv-apex/``). These files are named with the naming convention os-sdn_controller-enabled_feature-[no]ha.yaml. These files can be used in place of the (``/etc/opnfv-apex/deploy_settings.yaml``) file if one suites your deployment needs. If a pre-built deploy_settings file is choosen there is no need to customize (``/etc/opnfv-apex/deploy_settings.yaml``). The pre-built file can be used in place of the (``/etc/opnfv-apex/deploy_settings.yaml``) file. 2. network_settings.yaml This file provides Apex with the networking information that satisfies the prerequisite `Network Requirements`_. These are specific to your environment. Running ``opnfv-deploy`` ------------------------ You are now ready to deploy OPNFV using Apex! ``opnfv-deploy`` will use the inventory and settings files to deploy OPNFV. Follow the steps below to execute: 1. Execute opnfv-deploy ``sudo opnfv-deploy [ --flat ] -n network_settings.yaml -i inventory.yaml -d deploy_settings.yaml`` If you need more information about the options that can be passed to opnfv-deploy use ``opnfv-deploy --help`` --flat collapses all networks to a single nic, only uses the admin network from the network settings file. -n network_settings.yaml allows you to customize your networking topology. 2. Wait while deployment is executed. If something goes wrong during this part of the process, it is most likely a problem with the setup of your network or the information in your configuration files. You will also notice different outputs in your shell. 3. The message "Overcloud Deployed" will display when When the deployment is complete. Just above this message there will be a URL that ends in port http://:5000. This url is also the endpoint for the OPNFV Horizon Dashboard if connected to on port 80. .. _`Execution Requirements (Bare Metal Only)`: requirements.html#execution-requirements-bare-metal-only .. _`Network Requirements`: requirements.html#network-requirements .. Revision: ca6426c31c73a8889c66a0a5c08e059103dfff9a Build date: 2016-05-13